PDA

Zobacz pełn± wersję : Regeneracja "FELG ALUMINIOWYCH" (FOTO)



SAJENS
28-11-04, 14:32
Siemka moze komus sie przyda bo ja wlasnie zabieram sie za swoje i polakieruje je na czarno a po wakacjach rozejze sie za nowymi felusiami narazie trzeba pieniazki gromadzic i odkladac na cos lepszego.

Macie tutaj pokazane na fotkach jak latwo domowym sposobem zabrac sie za renowacje felg aluminiowch.
http://img109.exs.cx/img109/9799/4297.jpghttp://img109.exs.cx/img109/6960/4298.jpg
http://img109.exs.cx/img109/5899/4299.jpghttp://img109.exs.cx/img109/9895/4300.jpg
http://img109.exs.cx/img109/7711/4302.jpghttp://img109.exs.cx/img109/2668/4303.jpg
http://img109.exs.cx/img109/9784/4304.jpghttp://img109.exs.cx/img109/8813/4305.jpg
http://img109.exs.cx/img109/9729/4306.jpghttp://img109.exs.cx/img109/6950/4307.jpg
http://img109.exs.cx/img109/8408/4308.jpghttp://img109.exs.cx/img109/4292/4309.jpg
http://img109.exs.cx/img109/8466/4310.jpghttp://img109.exs.cx/img109/9176/4311.jpg
http://img109.exs.cx/img109/4373/4312.jpghttp://img109.exs.cx/img109/8559/4313.jpg
http://img109.exs.cx/img109/2029/4314.jpghttp://img109.exs.cx/img109/8652/123412.jpg

EFEKT NIEZLY !!!

POZDROWIENIA SAJENS

hosi
28-11-04, 14:55
:shock: Elegancko!
Jaki¶ opis do tego? Jakie ¶rodki zostały do tego użyte itp?

Mystek
28-11-04, 15:04
E no wyszly elegancko naprawde dobra robota :!:

Tomo
28-11-04, 15:08
no ja swoje bede wlasnie regenerowal wkrotce ale sam ich nie naprostuje a wiadomo ze warto to zrobic ;)

sc0rpion
28-11-04, 15:30
kolejny beznadziejny temat :?

LIO
28-11-04, 15:49
kolejny beznadziejny temat :?
daj lepszy, czekamy :?

Sajens, te felgi, to chyba ktos sam uj**al bulka tarta z maslem ;) zeby na takie zniszczone wygladaly.
Spoczko.

sc0rpion
28-11-04, 15:58
rzeczywiscie bardzo wiele mozna sie dowiedziec na temat regeneracji felg domowym sposobem :lol: :lol:

Saxo Rulez
28-11-04, 16:01
The surface of aluminium can be smoothed very easily and buffed to give a deep shine.

Allow your engine to cool down before working under the bonnet. Using a suitable Torx bit, remove the black plastic cover which sits between the two head covers. Under the cover you will see the dual coils...
Using the same Torx bit you should now remove the 16 screws which hold the two head covers in place. The front cover may now be removed.
Before removing the rear cover from the engine you should disconnect the crankcase oil breather pipe from the righthand corner of the head cover. The inlet manifold pressure pipe must also be disconnected from the head cover/throttle body.
http://www.sax-p.com/photos/inline/photo0994.jpg

With both covers now removed from the engine bay, you should place them on a flat work surface. Take care not to damage the oil seal on the underneath of each head cover, as if this seal is ripped you will have to re-seal the head cover.
Most VTS head covers come as standard with a layer of silver paint and lacquer. Many engines also seem to be released to the customer with a thick wax protective layer remaining. This can be quite stubbarn to remove.
http://www.sax-p.com/photos/inline/photo0985.jpg
You must now remove the paint from the head covers and flatten the surface. There are a number of ways of doing this depending on what tools you have available to you. Probably the easiest universal method it to use an electric sander.
Starting with a fairly rough grade of wet and dry paper (80 Grade) the surface of both head covers should be worked over until the dull aluminium surface can be seen all over.

http://www.sax-p.com/photos/inline/photo0986.jpg

The head covers should next be re-worked using 400 Grade wet and dry paper and when a consistent surface is achieved, the process should be repeated using 1000 Grade wet and dry paper.
At this point a very smooth surface should have been created. Lots of pressure should be used in order to get a truly smooth finish. The more preparation work put into this job, the better the end result will be.
http://www.sax-p.com/photos/inline/photo0983.jpg

When you are happy with the quality of the surface it is time to start the polishing stage. I have tried many different types of metal polishes and have found the most efficient polish for this job to be "Autosol". This is available from most general motor accessory outlets.
Plenty of polish should be smeared across the surface of the head covers. The electric sander should now be used to work the metal polish into the head covers, using a soft cloth in place of sand paper!
http://www.sax-p.com/photos/inline/photo0992.jpg

Troche tego jest....

Mystek
28-11-04, 16:16
Tja po pierwsze strona tylko dostepna dla uzytkownikow a po drugie skoro tam masz opisane to czego jeszcze od nas oczekujesz ?! zeby ktos ci to samo powiedzial ?! Ehh ...

Tomo
28-11-04, 16:20
http://www.sax-p.com/mods/show-article.asp?artid=28

To może takie nie dokonca OT :P , ale jest opisane jak spolerować pokrywe zaworów. Przy okazji jest opisane jak to zrobić dokładnie i czym. Może się okazać pomocne dla kogo¶.

skopiuj jakos to i wklej zeby mozna bylo przeczytac

Pati
28-11-04, 16:56
te foty sa o ile pamietam z honda-tech i tam do tego byl jeszcze opis czego uzywac, czym smarować i jak malować. no i fotki były nromalnie ustawione :) proponuje Sajens, zebys wrocil na Honda-tech i zapodal jeszcze opis...

Saxo Rulez
28-11-04, 17:41
to czego jeszcze od nas oczekujesz ?! zeby ktos ci to samo powiedzial

Nie bardzo to rozumiem? Podałem to ponieważ tematem topicu jest polerowanie felg samemu jak Adam Słodowy, ludzie pytali czego się do tego używa, więc podaje przykład jak post±pić z innym aluminowym elementem. Logiczne że znam tego tresć a podaje j± tym co nie znaj±

Mystek
28-11-04, 18:01
No ale w innym temacie pytasz o polerke pokrywy zaworow a tutaj sam wrzucasz odpowiedz na swoje pytanie ...

nowy125
28-11-04, 18:04
No ale w innym temacie pytasz o polerke pokrywy zaworow a tutaj sam wrzucasz odpowiedz na swoje pytanie ...

posty se nabija (jak ja teraz;) ) chce być mega gejem

Saxo Rulez
28-11-04, 18:10
Czytajcie tematy Civic Geje :grin: Pytam o polakierowanie pokrywy zaworów - a to chyba jest różnica.

SAJENS
28-11-04, 18:10
Dokladnie fotki sa z forum z usa i opis bedzie dorzucony niebawem pracuje nad nim :).
Od czasu do czasu bede wrzucal znalezione na innych forach zeczy zeby bylo to wszystko na naszym w jednym miejscu. A napewo sie to komus przyda.

Pozdrawiam SAJENS

nowy125
28-11-04, 18:14
Czytajcie tematy Civic Geje :grin: Pytam o polakierowanie pokrywy zaworów - a to chyba jest różnica.

czytam lisku dokładnie , nietylko tematy. napisałe¶ cytuję : "A btw ile takie polerowanie może kosztować? A może sam mogę to zrobić?"

Saxo Rulez
28-11-04, 18:25
Oj b±kneło mi się co¶ przez przypadek :oops:
Ogólnie to chce pomalować w czerwony mat :D

GTBart
28-11-04, 23:53
a ja zapytam tylko: jakiego lakieru do tego trzeba uzyc, zeby byl taki polysk lustrzany??

Gr00bY
29-11-04, 00:26
Bezbarwnego :wink:

GTBart
29-11-04, 00:36
HEHE ta jasne nagle z obdrapanego chromu, przemalowanego podkładem pojawiło sie lusterko po pomalowaniu bezbarwnym :D
No a teraz serio, jakiego lakieru użyć??

SAJENS
29-11-04, 00:44
Z tego co kiedys pytalem w mieszalni Siekensa to do lakierowania felg uzywa sie lakierow stosowanych do malowania samochodow ciezarowych. Sa one duo twardsze i wystrzymalsze nie odpryskuja i wlansie w swoim skladzie posiadaja suplementy ktore nadaja polysk po lekkim polerowaniu. Bo wiadoma zecza jest ze trzeba je jeszcze wypolerowac chyba ze ktos mat nadaje.
Ja swoje polakieruje na kolor czarny. Wygladem troszczke przypomina spoon style :) a w koloze czarnym beda ladnie sie komponowac z niska zawieszka :).


http://img26.exs.cx/img26/6503/fela.jpghttp://img26.exs.cx/img26/1792/1082374819782_1082250474578_SW_037.jpg
TE SA MOJE --------------------TAKIE CHCEM ZROBIC :)
http://img14.exs.cx/img14/4558/fela1.jpg


Troszeczke podobne prawda teraz trzeba tylko polakierowac zorbic naklejeczke spoon :) albo pomalowany lakierem napis czerwony i mamy super fele :) hihi ale ze mnie kombinator :)

Co o tym myslicie uda sie >?



Pozdrowionka SAJENS

Tomo
29-11-04, 01:01
daj inne foto swojej felgi

Mystek
29-11-04, 02:51
wyjdzie fajnie ale ja bym zostawil rant wypolerowany a reszta na czarno wtedy ladnie kontrastuje .... 8)

SAJENS
29-11-04, 11:43
No nie wiem czy z tym rantem sie bawic zwlaszcza ze te felgi co mam to 2 kobiety na nich jezdzily i ranty albo lekko trzeba bedzie z toczyc albo papierek i heja wypolerowac a puzniej to juz nie bedzie tak latwo na lustro zrobic.
Wydaje mi sie ze pociagne je cale lakierem tylk teraz pytanie czy pomalowac je na mat czy pociagnac lakierem z polyskiem.
Tak sie zastanawiam i coraz bardziej przkeonuje sie matowego koloru.
No i chyba dekielka nie bede zakladal :) Jeszcze zobaczymy cala zima na zmodyfikowanie fleg.
POzdrowionka SAJENS

badyl
29-11-04, 12:39
niech ktos to przetłumaczy,jakis uczony mega gej,bo jestem ciekawy co to za srodki i ile kosztuje :D